Products
TaşStop® Ultra SLV Solvent Based Decorative Stone Binder
Product Description
ULTRAMAX 1K is a high-strength, UV-resistant, non-yellowing, single-component stone carpet resin based on aliphatic polyurethane, suitable for indoor and outdoor applications.
Areas of Use:
Used in indoor and outdoor floor coverings, insulated terrace and balcony floors, permeable floor applications exposed to high water levels, showrooms, common areas, and areas requiring high strength under heavy loads. Note: For the appropriate thickness of Isopave Stone Carpet depending on traffic load, please consult our technical team.
Components: Polyurethane
Color: Transparent-Glossy
Solid Content: 100%
Usage Rate: 5% - 7% of stone weight
Mixing Ratio: Single-component, ready to use
Density: ~1.15 g/lt
Application Time: 45-55 min (varies depending on air temperature)
Viscosity (Brookfield 25 °C): 3000-4000 mPa.s
Application Temperature: 5°C - 30°C
Initial Curing: > 24 hours
Opening to Pedestrian Traffic: > 48 hours
Full Curing Time: 7 days
Single component.
Easy to apply.
Prevents moss formation. (Maintenance recommendations must be followed.)
Prevents staining.
UV resistant. Does not yellow.
Permeable. Does not accumulate water on the surface.
Solvent-free. Odorless.
Suitable for indoor and outdoor use.
Resistant to high and low temperatures.
Preserves the color of stones.
The climatic conditions of the application area are extremely important. If the area is subject to freeze-thaw cycles, extra precautions must be taken during surface preparation. The application of stone carpet requires proper and permanent adhesion to the surface. Therefore, the application should be done on concrete of at least C20 quality or on a solid asphalt surface. In harsh climates, the concrete surface requires extra processing due to freeze-thaw cycles. In such climatic conditions, it is essential to remove the weak grout layer from the concrete surface by grinding it with diamond-tipped grinding machines. After surface grinding, any cracks should be opened in a V shape and repaired with epoxy repair mortar. Afterwards, IsoPrimepox or IsoPrime PU primer should be applied to the surface. To increase the surface roughness before application, optional extra sandblasting with 1-2 mm thick quartz sand can be preferred before the primer dries. Before mixing, ensure that the stones are dry and dust-free. The resin should be mixed and prepared in the specified ratio. The mixture should be made according to the ideal resin ratio and ensure that the mixture is homogeneous. The stones should be placed in the mixer, and the resin should be added afterwards. To ensure an ideal mixture, the Isopave Stone Carpet Mixer, specifically designed for stone carpets, should be used. After a 5-minute mixing process, ensure the resin coats all the stones, making sure no dry areas remain. The amount of resin to be used varies between 5% and 7% depending on the surface structure and size of the stone. Using too much resin will cause foaming, so care should be taken to use the optimum amount of resin. When mixing with a hand mixer using a bucket measure, the bottom of the bucket may not be a homogeneous mixture. In such a case, the mixture should be transferred to a different bucket, and if necessary, mixing should continue in the new bucket.
Ensuring thickness homogeneity and surface smoothness is extremely important in stone carpet applications. Therefore, after the stones are laid on the ground, a leveling trowel and special Isopave Pulling Trolleys should be used to spread them. After spreading, application should be done to the surface using special trowels lubricated with Isopave Trowel Oil. It should be remembered that applying pressure to the surface during application will make the stones adhere more tightly and interlock. If thinner or similar solvents are used instead of oil, the solvent will thin the resin on the surface, reducing the adhesion strength of the stones. Similarly, foaming may occur when applying with soapy water, so the quality of the oil used is of great importance. For high-meterage applications, finishing with a special Isopave Lightweight Finishing Machine should be preferred.
If slip resistance is desired immediately after application, Isopave Glass Powder can be sprinkled to finish the surface.
- Surface problems may occur in applications performed in environments below +5 ºC and above +35 ºC.
- Application surfaces must be dry and clean.
- Safety precautions specified on the can and in the TDS should be taken before application.
- Application should be carried out according to the specified application characteristics.
- After partial use; the container should be tightly closed and care should be taken to prevent air from entering the container.
- Contact with skin and eyes should be avoided; in case of contact, wash with plenty of water and consult a doctor.
- The product should not be in contact with water during the drying time.
- Immediately after application, before the resin hardens, equipment should be cleaned with cellulosic thinner.
- Taş Hal is not a waterproofing material and is permeable. It is recommended that waterproofing be done before application in indoor and outdoor areas where impermeability is desired.
- Empty containers should not be used to store food or drinking water.
- Safety and Health Warnings:
- Protective goggles, clothing and gloves should be worn.
- Avoid contact with skin, eyes and clothing.
- The product must be prevented from spreading into the environment.
- Eating, drinking, and smoking should be avoided during use.
- All packaging and containers should be carefully packaged to minimize spills.
- Containers should be kept tightly sealed when not in use.
- Keep away from heat, sparks, flames, and hot surfaces.
- Broken packages should not be handled without protective equipment.
- Empty containers should not be reused. They should be treated as contaminated waste.
- If clothing becomes soiled, it should be removed immediately and washed before reuse.
- The product should be stored in clearly labeled containers.
- Keep out of reach of children.
- Keep away from food, beverages, and animal feed.
- Storage should only be in the original container.
- Containers should be stored upright in a cool, well-ventilated place, tightly closed.
- Containers should be protected from damage.
- The data and recommendations or other support services contained in this document are based on our current knowledge and experience and are provided to the best of our knowledge. Given the numerous factors that may affect the processing and application of our products, this data does not exempt processors from conducting their own research and testing, particularly regarding the suitability of the supplied goods for the processes and purposes for which they are intended; nor does this data constitute a guarantee of specific properties or the suitability of the product for a particular purpose. Any description, drawing, photograph, data, ratio, weight, measured value, etc., given herein are subject to change without prior notice and do not constitute the agreed contractual quality of the product. It is the responsibility of the buyer of our products to ensure that all proprietary rights and applicable laws and regulations are complied with.
5kg Plastic Drum, 20kg Plastic Drum
Can be stored for one year in unopened original packaging in environments between 5-35°C, away from direct sunlight. Must be protected from extreme temperatures and humidity.