Products
Isoprimepox Epoxy Based Solvent-Free Concrete Primer
Product Description
This is a two-component, epoxy resin-based, transparent primer that fills the capillary voids of concrete floors, increases concrete strength, and provides adhesion for stone carpet applications.
Areas of Use:
It is used as a primer before all stone carpet applications, epoxy and polyurethane-based coating systems, and under waterproofing applications such as PU and polyurea.
Resin Type: Epoxy
Color: Yellow (mixture)
Solid Content: 100%
Mixing Ratio (A+B): A: 66% B: 33%
Mixture Density: ~1.03 kg/lt
Application Time: 20-35 min (varies depending on air temperature)
Adhesion to Concrete: > 2 Mpa
Viscosity (Brookfield 25 °C): 400-500 cP
Application Temperature: 5°C - 30°C
Initial Curing: > 6 hours
Opening to Pedestrian Traffic: > 24 hours
Full Curing Time: 24 Hours (24 °C Room Temperature)
Suitable for indoor and outdoor use. Can be applied on damp, non-wet surfaces.
Solvent-free.
Cures quickly, easy to apply.
Has strong adhesion.
Provides impact protection.
Has excellent adhesion properties.
Fills capillary cracks in concrete by impregnation and creates an impermeable surface.
Prevents dusting when used as a top coat.
Can be applied to surfaces such as ceramic, marble, and metal.
Provides water resistance after curing and creates a barrier against moisture from below.
The surface must be clean, dry, and completely free of loose particles, grease, oil, or any substance that would prevent proper adhesion. If there are cracks or breaks in the surface, they must be repaired with epoxy or cement-based structural repair mortar before application. When preparing the product, component B is slowly added to component A and mixed with a mechanical mixer at low speed for 2 minutes until the mixture is homogeneous. Since the prepared mixture will react quickly, it should be used within 30 minutes. Care should be taken to ensure the material does not sit in the bucket; it should be poured onto the surface immediately and spread with a squeegee. This will prevent the rapid reaction of the material left in the bucket. On highly absorbent surfaces, a second coat can be applied 3-5 hours after the first coat. Reaction time is shorter in hot weather and longer in cold weather.
Consumption: 250-400 g/m² (varies depending on application thickness.)
- Surface problems may occur in applications performed in environments below +5ºC and above +35ºC.
- Application surfaces must be dry and clean.
- Application should be carried out according to the specified application characteristics.
- After partial use, the container should be tightly closed.
- Contact with skin and eyes should be avoided; in case of contact, wash with plenty of water and consult a doctor.
- The product should not be in contact with water during the drying time.
- Equipment should be cleaned immediately after application, before it hardens.
- Empty containers should not be used to store food or drinking water.
- Safety and Health Warnings:
- Protective goggles, clothing, mask, and gloves should be worn.
- Contact with skin, eyes, and clothing should be avoided.
- In indoor applications, attention should be paid to ventilation of the environment.
- The product should be prevented from spreading to the environment. It should be protected from direct sunlight.
- No eating, drinking, or smoking should be done during use.
- All containers and packaging should be carefully packaged to minimize spills.
- Containers should be kept tightly closed when not in use.
- They should be kept away from heat, sparks, flames, and hot surfaces.
- Broken packages should not be transported without protective equipment.
- Empty containers should not be reused. They should be considered contaminated.
- If clothing becomes soiled, it should be removed immediately and washed before reuse.
- The product should be stored in containers that are clearly labeled.
- Keep out of reach of children.
- Keep away from food, beverages, and animal feed.
- Storage should only be in the original container.
- Containers should be stored upright in a cool, well-ventilated place, tightly closed.
- Containers should be protected from damage.
- The data and recommendations or other support services contained in this document are based on our current knowledge and experience and are provided to the best of our knowledge. Given the many factors that may affect the processing and application of our products, this data does not exempt processors from conducting their own research and testing, particularly regarding the suitability of the supplied goods for the processes and purposes for which they are intended to be used; Furthermore, this data does not constitute a guarantee of specific characteristics or the suitability of the product for a particular purpose. Any description, drawing, photograph, data, ratio, weight, measured value, etc., given herein are subject to change without prior notice and do not constitute the agreed contractual quality of the product. It is the responsibility of the buyer of our products to ensure that all proprietary rights and applicable laws and regulations are complied with.
15kg SET (A: 10kg ,B: 5kg)
Direkt güneş ışığı almayan 5-35°C’lik ortamlarda, açılmamış orijinal ambalajlarında bir yıl depolanabilir. Aşırı sıcaklık ve nemden korunmalıdır. Kullandıktan sonra kap sıkıca kapatılmalıdır.