Products
Isobind 2K Pool 2K Polyurethane Resin for Pool Use
Product Description
ISOBIND 2K POOL is a two-component, high-strength stone carpet resin based on polyurethane with special chemical and hydrolysis resistance, specifically developed for pool use. It is suitable for indoor and outdoor pool interior and pool edge stone carpet applications.
Areas of Use:
Used in indoor and outdoor floor coverings, insulated pool interiors and surrounding areas.
Components: Chemically Resistant PU Resin
Color: Transparent-Glossy
Solid content: 100%
Usage rate: 5.5% – 6.5%
Mixing Ratio (A+B): A: 50% B: 50%
Mixing Density (A+B): ~1.10 – 1.15 gr/lt
Pot life: 20-30 min (varies depending on air temperature)
Viscosity (Brookfield 25 °C): 1500-2000 mPa.s
Application Temperature: 5°C - 30°C
Initial curing: > 36 hours at 20°C (Time shortens in hot weather)
Opening to pedestrian traffic: > 72 hours at 20°C
Full curing time: 7 days
It is a 2-component product.
Resistant to chemicals used in pools.
Resists oils, chemicals, and solvents without deterioration.
Easy to apply. Long application time.
Prevents algae formation.
Prevents staining.
Unaffected by continuous exposure to water.
UV resistant. Does not yellow.
Permeable. Does not accumulate water on the surface.
Solvent-free.
Suitable for all indoor and outdoor pool and poolside uses.
Resistant to high and low temperatures.
Preserves the color of stones.
The climatic conditions of the application area are extremely important. Ensuring proper and permanent adhesion to the surface is crucial for the application of stone carpet. Therefore, the application should be done on concrete of at least C20 quality or on a solid asphalt surface. If there are cracks on the surface, they should be opened in a V shape and repaired with epoxy repair mortar. Afterwards, Isoprimepox or Isoprime PU primer should be applied to the surface. If the surface is considered weak, it should be primed with Isoprimepox in two coats. Immediately after the second coat of primer, Isotex 160 and Isotex 300 mesh should be glued to the surface before the epoxy primer dries.
When applying the product to waterproofed surfaces (polyurea and cement-based), it is recommended to prime the surfaces with Isoprimepox. Mesh reinforcement is not necessary at this stage. Before mixing, ensure the stones are dry and dust-free. Components A and B should first be mixed together for 2 minutes using a drill. The stones should be placed in the mixer, and the prepared resin should be added immediately while the mixing process continues. To ensure an ideal mixture, the Isopave Stone Carpet Mixer, specifically designed for stone carpets, should be used. After a 5-minute mixing process, ensure the resin coats all the stones, making sure no dry areas remain. The amount of resin to be used varies between 6% and 7% of the stone's weight, depending on its surface structure and size. When mixing with a hand mixer using a bucket measure, the bottom of the bucket may not be homogeneous. In such a case, the mixture should be transferred to a different bucket, and mixing should continue in the new bucket.
Ensuring thickness homogeneity and surface smoothness is extremely important in stone carpet applications. Therefore, after the stones are laid on the ground, a leveling trowel and special Isopave Pulling Trolleys should be used to spread them. After spreading, application should be done using special trowels lubricated with Isopave Trowel Oil. It should be remembered that applying pressure to the surface during application will make the stones adhere more tightly and interlock. If thinner or similar solvents are used instead of oil, the solvent will thin the resin on the surface, reducing the adhesion strength of the stones. Applications using soapy solutions should be avoided as foaming may occur in the resin. For high-meterage applications, finishing with a special Isopave Lightweight Finishing Machine is preferred. If slip resistance is desired immediately after application, Isopave Glass Powder is sprinkled to finish the surface.
Application on Vertical Surfaces:
When applying to the vertical surfaces of pools, Isovert Thickening Powder should be used. Depending on the air temperature, the A and B components should be mixed with 1.5-1.75 times the volume of the resin by adding the powder mixture to achieve the desired consistency. Depending on the air temperature, the thickening powder should be added in a controlled manner until a firm gel consistency is achieved. Powder usage increases in hot weather and decreases in cold weather. The prepared mixture is first applied to the surface with a spatula. After approximately 10 minutes of waiting, the gel mixture is mixed with the stones at a rate of 6-6.5% and applied to the surface using a trowel tip, pressing down to achieve the final finish. Frequent lubrication of the trowel with Isopave Trowel Oil during application will make the process easier.
Note: For more detailed information, we recommend watching our application video on our website and contacting our technical team.
If you wish to fill the gaps between the pool stones for easy cleaning, please review the Isopave Pebble Deck system.
Consumption:
Stone weight X 5.5 - 6%
- Surface problems may occur in applications performed in environments below +5 ºC and above +35 ºC.
- Application surfaces must be dry and clean.
- Safety precautions specified on the can and in the TDS should be taken before application.
- Application should be carried out according to the specified application characteristics.
- After partial use; the container should be tightly closed and care should be taken to prevent air from entering the container.
- Contact with skin and eyes should be avoided; in case of contact, wash with plenty of water and consult a doctor.
- The product should not be in contact with water during the drying time.
- Immediately after application, before the resin hardens, equipment should be cleaned with cellulosic thinner.
- Stone Carpet is not a waterproofing material and is permeable. It is recommended that waterproofing be done before application in indoor and outdoor areas where impermeability is desired.
- Empty containers should not be used to store food or drinking water.
- Safety and Health Warnings:
- Protective goggles, clothing and gloves should be worn.
- Avoid contact with skin, eyes and clothing.
- The product must be prevented from spreading into the environment.
- Eating, drinking, and smoking should be avoided during use.
- All packaging and containers should be carefully packaged to minimize spills.
- Containers should be kept tightly sealed when not in use.
- Keep away from heat, sparks, flames, and hot surfaces.
- Broken packages should not be handled without protective equipment.
- Empty containers should not be reused. They should be treated as contaminated waste.
- If clothing becomes soiled, it should be removed immediately and washed before reuse.
- The product should be stored in clearly labeled containers.
- Keep out of reach of children.
- Keep away from food, beverages, and animal feed.
- Storage should only be in the original container.
- Containers should be stored upright in a cool, well-ventilated place, tightly closed.
- Containers should be protected from damage.
- The data and recommendations or other support services contained in this document are based on our current knowledge and experience and are provided to the best of our knowledge. Given the numerous factors that may affect the processing and application of our products, this data does not exempt processors from conducting their own research and testing, particularly regarding the suitability of the supplied goods for the processes and purposes for which they are intended; nor does this data constitute a guarantee of specific properties or the suitability of the product for a particular purpose. Any description, drawing, photograph, data, ratio, weight, measured value, etc., given herein are subject to change without prior notice and do not constitute the agreed contractual quality of the product. It is the responsibility of the buyer of our products to ensure that all proprietary rights and applicable laws and regulations are complied with.
A+B Set 33 kg (A: 16.5 kg / B: 16.5 kg)
Can be stored for one year in unopened original packaging in environments between 5-35°C, away from direct sunlight. Must be protected from extreme temperatures and humidity.