Products
Basf® Elastan® 120/S Aliphatic Based One Component Polyurethane Resin
Product Description
Elastan 120/S is a solvent-free, filler-free, and transparent 1K aliphatic polyurethane adhesive. It is a moisture-curing adhesive for bonding stone and mineral aggregates. Based on aliphatic resin polyurethane, its greatest feature is its ability to maintain the stone color stably after application, regardless of the cause. It has UV resistance and does not yellow. This feature allows it to be used with all stone colors. It is especially preferred for lighter colors.
Density (25°C): 1120 kg/cm³
Viscosity (25°C): 4200 mPa·s
NCO Content: 15.5%
Shelf Life: 6 Months
Color: Transparent
- LEED Certified
- Easy to apply due to its single-component nature
- Suitable for indoor and outdoor use
- Aliphatic
- Polyurethane Based
- UV Resistant
- Does not yellow
BASF ELASTAN 120 S Aliphatic Polyurethane Based Single Component Resin should be used in Stone Carpet applications at a rate of 5-7% of the stone weight. (Varies according to stone size.) Using too much or too little may cause negative results for the application. Contact us for correct use in your application area.
- Ideally, Isopave stone carpet application should be done between 5°C and 25°C.
- Resin usage should be within the specified range for application, and it should be ensured that the resin is mixed homogeneously.
- The stones to be used in the application must be dust-free and dry.
- Application should not be done in rainy weather.
- The application area must be dry, and contact with water should be avoided until curing is complete.
- Surface problems may occur in applications carried out in environments below +5 ºC and above +35 ºC.
- Application surfaces must be dry and clean.
- Safety precautions specified on the can and in the TDS should be taken before application.
- Application should be carried out according to the specified application characteristics.
- After partial use; the container should be tightly closed, and care should be taken to prevent air from entering the container.
- Contact with skin and eyes should be avoided; in case of contact, wash with plenty of water and consult a doctor.
- The product should not be in contact with water during the drying time.
- Immediately after application, before the resin hardens, equipment should be cleaned with cellulosic thinner. Stone Hal is not a waterproofing material and is permeable. For indoor and outdoor applications where impermeability is desired, it is recommended that waterproofing be done before application.
- Empty packaging should not be used to store food or drinking water.
- Safety and Health Warnings:
- Protective eyewear, clothing, and gloves should be worn.
- Avoid contact with skin, eyes, and clothing.
- Prevent the product from spreading to the environment.
- Do not eat, drink, or smoke while using the product.
- All packaging and containers should be carefully packed to minimize spills.
- Containers should be kept tightly sealed when not in use.
- Keep away from heat, sparks, flames, and hot surfaces.
- Do not handle broken packages without protective equipment.
- Empty containers should not be reused. They should be treated as contaminated waste.
- If clothing becomes soiled, it should be removed immediately and washed before reuse.
- The product should be stored in clearly labeled containers.
- Keep out of reach of children.
- If BASF products are intended for the manufacture of consumer goods (e.g., food or skin contact products, toys, etc.) or medical products, there are national and international laws and regulations that must be taken into account. Where these are not available, the applicable legal requirements of the European Union for consumer and medical products should suffice. The data and recommendations or other support services contained in this document are based on our current knowledge and experience and are provided to the best of our knowledge. Given the many factors that may affect the processing and application of our products, this data does not exempt processors from conducting their own research and testing, particularly regarding the suitability of the supplied goods for the processes and purposes for which they are intended; nor does this data constitute a guarantee of any particular properties or the suitability of the product for a particular purpose. Any description, drawing, photograph, data, ratio, weight, measured value, etc. given herein are subject to change without prior notice and do not constitute the agreed contractual quality of the product. It is the responsibility of the buyer of our products to ensure that all proprietary rights and applicable laws and regulations are complied with.
Metal Can
Polyurethane components are sensitive to moisture. Therefore, they should always be stored in closed, airtight containers.