Products
Basf® Elastan® 119 Aromatic Based Single Component Polyurethane Resin
Product Description
BASF® Elastan® 119 is a solvent-free, filler-free, and transparent 1K aromatic polyurethane adhesive. It is a moisture-curing adhesive for bonding stone and mineral aggregates. Thanks to the resin's special formulation, it can serve as a stone binder for decades. It is important to remember that complete infrastructure preparation is required for this.
BASF® Elastan® 119 Aromatic Resin is chemically and physically resistant to UV rays and only causes surface yellowing. Apart from yellowing, there is no loss in the resin's bonding structure. Aromatic resins offer significant cost savings during application, and yellowing is minimized when used with warm-colored stones. Over time, as the surface wears down (6-12 months depending on usage), the stones regain their original color.
Yoğunluk (23°C): 1,13 g/cm³
Viskozite (25°C): 1600 mPa·s
NCO İçeriği: % 20,8 G 133-06
Raf Ömrü: 6 Ay
Renk: Şeffaf, kehribar
- LEED Certified
- Easy to apply due to its single-component nature
- Suitable for indoor and outdoor use
- Aromatic
- Polyurethane Based
BASF ELASTAN 119 Aromatic Polyurethane Based Single Component Resin should be used in Stone Carpet applications at a rate of 5-7% of the stone weight. (Varies according to stone size.) Using too much or too little may cause negative results for the application. Contact us for correct use in your application area.
- Ideally, Isopave stone carpet application should be done between 5°C and 25°C.
- Resin usage should be within the specified range for application, ensuring that the resin is homogeneously mixed with the aggregate.
- Aggregates used with the resin must be dust-free and dry.
- Application should not be done in rainy weather.
- The application area must be dry, and contact with water should be avoided until curing is complete.
- Surface problems may occur in applications performed in environments below +5ºC and above +35ºC.
- Application surfaces must be dry and clean.
- Safety precautions specified on the can and in the TDS should be taken before application. Application should be carried out according to the specified application characteristics.
- After partial use; the container should be tightly closed, and care should be taken to prevent air from entering the container.
- Contact with skin and eyes should be avoided; in case of contact, wash with plenty of water and consult a doctor.
- The product should not be in contact with water during the drying period.
- Immediately after application, before the resin hardens, equipment should be cleaned with cellulosic thinner.
- Stone Hal is not a waterproofing material and is permeable. For indoor and outdoor areas where impermeability is desired, it is recommended that waterproofing be done before application.
- Empty packaging should not be used to store food or drinking water.
- Safety and Health Warnings:
- Protective eyewear, clothing, and gloves should be worn.
- Avoid contact with skin, eyes, and clothing.
- Prevent the product from spreading to the environment.
- Do not eat, drink, or smoke during use.
- All packaging and containers should be carefully packaged to minimize spills.
- Containers should be kept tightly sealed when not in use.
- Keep away from heat, sparks, flames, and hot surfaces.
- Do not handle broken packages without protective equipment.
- Empty containers should not be reused. They should be treated as contaminated waste.
- If clothing becomes soiled, it should be removed immediately and washed before reuse. The product should be stored in clearly labeled containers.
- Isocyanates irritate the eyes, respiratory organs and skin. Sensitization may occur by inhalation and skin contact.
- MDI is harmful to the respiratory tract. When handling them, observe the necessary precautions described in the Material Safety Data Sheets (MSDS).
- Keep out of reach of children.
- If BASF products are intended to be manufactured as consumer products (e.g. food or products requiring skin contact, toys, etc.) or medical products, there are national and international laws and regulations that must be taken into account.
- Where these are not available, the applicable legal requirements of the European Union for consumer products and medical products should suffice. The data and recommendations or other support services contained in this document are based on our current knowledge and experience and are provided to the best of our knowledge. Given the many factors that may affect the processing and application of our products, this data does not exempt processors from conducting their own research and testing, particularly regarding the suitability of the supplied goods for the processes and purposes for which they are intended to be used; furthermore, this data does not constitute a guarantee of any particular properties or the suitability of the product for a particular purpose. Any description, drawing, photograph, data, ratio, weight, measured value, etc. given herein are subject to change without prior notice and do not constitute the agreed contractual quality of the product. It is the responsibility of the buyer of our products to ensure that all proprietary rights and applicable laws and regulations are complied with.
Metal Can
Polyurethane components are sensitive to moisture. Therefore, they should always be stored in closed, airtight containers.
For more detailed information, please refer to the separate data sheet entitled "Information on incoming material control, storage, material preparation and waste disposal" and component data.